農機大全網（m.97661a.com）今天給各位分享機械專業英語在線翻譯1的知識，其中也會對機械專業英語在線翻譯1進行解釋，如果能碰巧解決你現在面臨的問題，別忘了關注本站，現在開始吧！

本文導讀目錄：

1、機械專業英語在線翻譯1

2、機械專業英語對照漢語的文章1

3、機械中什么叫做工藝 什么叫工序 什么是沖壓 冷熱沖壓有何區別 軋鋼是什么 用什么工具1

機械專業英語在線翻譯1 ♂

機械專業英語在線翻譯

Electric hoist bridge crane is a small light lifting equipment. Gourd with small size, light weight, simple operation, easy-to-use features such as for industrial and mining enterprises, storage terminals and other places.By electric hoist motor, drive mechanism and the composition of drum or sprocket can be used alone can also be assembled together with the car flying in the use of a crane beam, LH electric double-beam bridge crane hoist with the traditional double-beam bridge crane is the difference between electric hoist drum to replace the small car, motor. Reducers, brakes and other lifting devices. This article mainly deals with electric hoist bridge crane to do the main body of analysis and calculation, including the electric hoist lifting body, and the operation of car bodies.

機械專業英語對照漢語的文章1 ♂

機械專業英語對照漢語的文章

Three crossflow (No.1-No.3) dryers were tested. Dyer No.1 contains two crossflow columns, each column consists of two drying sections, one turn-flow device and a cooling section, and with a grain column thickness in the upper drying section of 0.277m and 0.304m in the lower section. The dimensions of dryer No.1 are 6.517m×3.400m×13.482m. No.2 dryer is similar to No.1, but is smaller and has a lower capacity. No.3 is a cylindrical crossflow dryer with two drying sections, one turn-flow device and a cooling section.

The mixed-flow dryer (No.4) is composed of eight modular sections. Each module has dimensions of 1.8m×1.0m×0.8m. The tow bottom modules serve as cooling stage. Dryer No.5 consists of two mixed-flow drying towers in series, similar in design as dryer No.4.

Dryers No.6-No.10 are concurrent-/counter-flow dryers, consisting of two or more towers. The number in front of “-CCF” indicates the number of towers. Each tower has two counter-/concurrent-flow drying sections. The last tower, or part of the last tower, is used for cooling. The depth of the counter-/concurrent-flow beds is 0.6m, the cross-sectional area of each tower is 2.2m×2.2m. It should be noted that overseas CCF dryers do not have counter-flow drying stages, only a counter-flow cooling stage.

The steam dryer is a unique dryer widely used in grain depots in China. It consists of 3-6 indoor drying and cooling towers, and a boiler. Each tower contains in its upper section a series of steam pipes, and in its lower section a number of inlet/outlet air ducts. The grain is heated by conduction as it flow over the steam-heated pipes, and is subsequently treated with ambient or slightly-heated recycled drying-air. The steam pressure in the pipes is 2×105Pa--4×105Pa (130-140℃), the diameter of the pipes is 42-48mm, and the distance between pipes is 110-120mm. The grain retention time is long (4-6 hours for 10-point moisture removal) due to the relatively low grain temperature.

Sun drying is still the main method of grain drying in China. Almost every village or depot has a special area for the sun drying of grains. The grain is spread out in 5-10cm thin layer and is stirred occasionally. In Northeast China where the ambient temperature is very low when maize is harvested, sun drying is a very slow process.

三橫(一號至三號)烘干設備進行了測試. 戴先生no.1包含兩個橫欄,每欄分為兩部分干燥, 一轉流器及冷卻段, 與糧食柱厚度在上部干燥部分0.277m和0.304m在下游. 尺寸干燥器一號是6.517m×3.400m×13.482m. 二號烘干機相似一號,但規模較小,具有容量較低. 第三是橫向圓筒烘干機烘干兩部分,一部分是轉流裝置和冷卻段. 混流式干燥機(四號)是由八個單元章節. 每個單元尺寸1.8×1.0×0.8米. 拖車底部模塊作為冷卻階段. 干燥器no.5分為兩個混流干燥塔系列,類似的設計作為烘干四號. 干衣no.6-no.10都是concurrent-/counter-flow烘干機,由兩個或兩個以上的彈孔. 數年前的"框架",表明了很多水塔. 每個塔有兩個counter-/concurrent-flow曬路段. 最后塔,或部分上塔,是用于冷卻. 有深度的counter-/concurrent-flow病床0.6m,橫截面的每個塔有2.2m×2.2m. 應當指出,海外ccf干衣沒有反流干燥階段,只有一個反流冷卻階段. 蒸氣烘干是一個獨特的烘干機廣泛用于糧庫中. 它由3-6室內干燥,冷卻水塔,一臺鍋爐. 每個塔載在其上部一系列的蒸汽管道, 而在其下游的一系列進/出水口風筒. 谷物的熱傳導,因為它流了蒸汽加熱管, 并隨后處理空氣或微循環加熱干燥的空氣. 蒸汽壓力管道2×105pa--4×105pa(130-140℃),直徑較小的管材是42-48mm, 之間的距離和管道是110-120mm. 糧食停留時間很長(4-6小時,10點去濕)由于相對較低的糧食溫度. 晾曬仍然是主要的方法谷物干燥中. 幾乎每一個村或倉庫具有特殊的地區,以供晾曬谷物. 糧食是分布在5-10cm薄層,偶爾攪拌. 在東北那里的氣溫很低,當玉米收割, 太陽曬是一個非常緩慢的過程

機械中什么叫做工藝 什么叫工序 什么是沖壓 冷熱沖壓有何區別 軋鋼是什么 用什么工具1 ♂

機械中什么叫做工藝 什么叫工序 什么是沖壓 冷熱沖壓有何區別 軋鋼是什么 用什么工具

工序
一個或一組工人在同一工作地對同一個或同時對幾個工件所連續完成的那一部分工藝過程被稱為工序。
例如，
一個工人在一臺車床上完成車外圓、端面、空刀槽、螺紋、切斷；
一組工人刮研一臺機床的導軌；
一組工人對一批零件去毛刺。

生產和檢驗原材料、零部件、整機的具體階段。
在生產過程中，直接改變原材料（或毛坯）形狀、尺寸和性能，使之變?yōu)槌善返倪^程，稱為工藝過程。它是生產過程的主要部分。例如毛坯的鑄造、鍛造和焊接；改變材料性能的熱處理；零件的機械加工等，都屬于工藝過程。工藝過程又是由一個或若干個順序排列的工序組成的。

工序是工藝過程的基本組成單位。所謂工序是指在一個工作地點，對一個或一組工件所連續完成的那部分工藝過程。構成一個工序的主要特點是不改變加工對象、設備和操作者，而且工序的內容是連續完成的。
沖壓工藝性是指沖壓件對工藝品的適應性，即所設計的沖壓件在尺寸大小、尺寸精度與基準、結構形狀等是否符合沖壓加工的工藝要求。

沖壓--是在室溫下，利用安裝在壓力機上的模具對材料施加壓力，使其產生分離或塑性變形，從而獲得所需零件的一種壓力加工方法。
沖壓模具--在冷沖壓加工中，將材料（金屬或非金屬）加工成零件（或半成品）的一種特殊工藝裝備，稱為冷沖壓模具（俗稱冷沖模）。